Sealed glass unit replacement
Foggy Window Repair in Toronto & the GTA
Fog, haze, or water droplets trapped between the panes mean the seal on the glass unit has failed. In most cases we replace only the sealed unit and keep the window frame you already have.
- Glass-only replacement
- Frame stays in place
- Measured on site
- Written quote first

Fix N Clean replaces failed insulated glass units (IGUs) in double- and triple-pane windows across Toronto, North York, Scarborough, Etobicoke, Mississauga, Vaughan, Markham, Richmond Hill, and Brampton. A foggy window is a glass problem, not a frame problem, so the repair is usually a new sealed unit made to fit your existing frame rather than a full window replacement. Call or text (365) 360-4168 with a photo for a quote.
What to look for
Signs the seal has failed
If you can wipe it off, it is surface condensation. If you cannot reach it from either side, the sealed unit has failed.
- Fog, haze, or a milky film you cannot wipe off from inside or outside
- Water droplets or streaks running between the panes
- White mineral marks on the inner glass surfaces after repeated wet and dry cycles
- Fogging that comes and goes with the weather and gets worse each season
- One pane in a multi-pane window that looks different from the others
- Glass that feels noticeably colder in winter than neighbouring windows
Why windows fog between the panes
A double- or triple-pane window is built around an insulated glass unit: two or three sheets of glass bonded to a spacer bar and sealed around the edge, with dry air or argon gas in the gap. The spacer holds a desiccant that absorbs the small amount of moisture inside. When the edge seal breaks down, from age, sun exposure, building movement, or water sitting in the frame, outside air starts moving in and out. Once the desiccant is saturated, moisture condenses between the panes where you cannot reach it.
The fog is the visible symptom. The unit has also lost the dry, sealed gap that gives it its insulating value, and any gas fill has leaked away, which is why a fogged window often feels colder in winter. Condensation on the room-side surface of the glass is a different issue, usually indoor humidity; our guide to fog between the panes explains how to tell them apart.
Replace the glass, keep the frame
If the frame is square, solid, and operating properly, the failed unit can be removed and a new one installed in the same sash or frame. We measure the glass size, the overall thickness, the spacer, and any low-E coating or grilles so the new unit matches the rest of the house. The sealed unit is made to order, then installed and secured with the original stops or new glazing bead.
This is far less disruptive than replacing the window: no interior trim work, no exterior capping, and no change to the look of the opening. It works for fixed picture windows, casements, sliders, single- and double-hung sashes, and the glass in sliding patio doors.
When a full window replacement makes more sense
Glass-only repair is not always the right call. If the frame is rotted, warped, or leaking, if the hardware is failing and parts are no longer made, or if several units in the same old windows are failing one after another, new windows may be better value over time.
We check the frame before quoting and tell you plainly which way the numbers lean. See window replacement for how a full installation is measured and priced.
What about defogging services?
Some companies drill small holes in the glass, dry out the unit, and plug or vent the holes. This can clear the view for a time, but it does not restore the original edge seal or replace lost gas fill, so the insulating performance stays reduced and the fog can return.
Replacing the sealed unit deals with the cause rather than the symptom, which is why it is the repair we carry out.
Step by step
How a foggy window repair works
Two short visits: one to measure, one to install.
Send photos or book a visit
Text or upload photos of the window from inside and outside, with your city. Photos usually show whether it is a sealed-unit failure.
On-site measurement
We measure the glass, unit thickness, and spacer, note any low-E coating, tint, or grilles, and check the frame and sash.
Written quote
You get the price for each unit in writing before anything is ordered.
Custom glass is made
The new sealed unit is manufactured to the measured size, typically within 24–48 hours for standard glass. Shaped, tempered, or oversize units take longer.
Installation
The old unit comes out, the frame channel is cleaned, and the new unit is set, blocked, and secured. A single unit usually takes under an hour.
Transparent pricing
Foggy window repair cost
Published ranges for typical residential units. Your price is confirmed in a written quote after measuring.
| Service | Price Range (CAD) | Timeline |
|---|---|---|
| Foggy window sealed-unit replacement | $149 – $250 | 24–48 hrs for glass |
| Double-pane thermal unit (IGU) | $175 – $320 | 24–48 hrs for glass |
| Sliding patio door glass | $195 – $350 | Same day for stocked sizes |
| New window installation (per opening) | $650 – $1,800 | Order + 1–2 weeks |
What changes the price
- Glass size and overall unit thickness
- Double- or triple-pane construction
- Low-E coating, argon fill, tint, or obscure glass
- Tempered or laminated safety glass where required
- Grilles between the panes or shaped units
- Access: upper floors and fixed units over stairs or roofs
Request a written quote with photos and your city, or call (365) 360-4168.
Coverage
Foggy Window Repair across the GTA
Common questions
Foggy Window Repair FAQ
In most cases, yes. Fog between the panes means the sealed glass unit has failed, not the frame. When the frame and sash are sound, we replace only the insulated glass unit, made to the size and thickness of the original.
Our published range for a typical residential sealed-unit replacement is $149–$250 per unit, with larger or low-E double-pane units running $175–$320. Size, glass type, and access change the price, so the exact figure is confirmed in a written quote after measuring.
Measuring takes a few minutes per window. The new unit is custom-made, typically within 24–48 hours for standard glass, and installing a single unit usually takes under an hour. Shaped, tempered, or oversize units can take longer to produce.
We match the visible details: glass thickness, spacer colour, low-E tint, obscure patterns, and grilles between the panes where they exist. Tell us if neighbouring windows have a tint or coating so it can be checked during measurement.
Not usually. A fogged unit is still weathertight, so it can be booked as planned work. It will not clear by itself, though, and mineral deposits can etch the inner glass over time, so the view keeps getting worse. Cracked or broken glass is different and should be dealt with promptly.
Yes. The fixed and sliding panels of a patio door use sealed units that can be replaced in the existing door, normally in tempered safety glass.
24/7 dispatch · Toronto & GTA
Ready for a written quote?
Call or text (365) 360-4168 for current availability, or send photos through the quote form and get the scope and price in writing before work begins.
